M104 Gas Engine Head Gasket Replacement Part 3: Cleaning, Inspection & Parts to Order - On Demand Video

If you want your head gasket repair to last these are the important steps you must follow

The head has been successfully removed. There is quite a bit of work that will need to be done before the head is ready to go back on. The head and the block will need to be cleaned and inspected and parts will need to be ordered. Other parts should be replaced while the head is off the engine. These are the subjects discussed in this third part in Kent’s M104 head gasket video manual series.

M104 Gas Engine Head Gasket Replacement Part 3: Cleaning, Inspection & Parts to Order - On Demand Video
$14.99
SKU:
VM-104HG3
On Demand Video

Product Details

The following specifics will be covered:

  • Review of removing the head with an engine hoist and tilter
  • Why the tilter is so important
  • Removing the old gasket and examining it for cause of leaks
  • Inspection of the block for damage
  • Cleaning top surface of the block
  • Cleaning and inspection cylinder head bolt threads in the block
  • Why it is so important to test the block threads
  • Inspection of the cylinder head for damage
  • Cleaning the gasket material of the head without damaging the aluminum
  • What to use to prevent scratching the surface
  • How to check for warpage of the block and head
  • Checking for leaks in other gaskets
  • Other parts to order in and around the manifold and the engine
  • Checking the cylinder head bolts for excessive stretch
  • When the bolts should be replaced
  • Where to order the parts
  • Other parts to consider replacing while the head is off
  • Discussion and overview of new parts received and why they are recommended
  • New updated head gasket shown up close
  • New updated manifold gaskets shown up close
  • Other work that should be done under the manifold while head is off
  • Good example why you want to replace the exhaust manifold gaskets
  • Checking and painting the exhaust manifolds
  • How to clean the head in a solvent bath
  • Consider testing / or replacing the fuel injectors and injector seals
  • Reference to next video in the series - installing the head.

Not covered in this video: Once again please keep in mind that Kent does not go over removing and replacing every single bolt, nut or clamp. It is assumed that if you are tackling an advanced DIY job like a head gasket replacement you will already know some of the “basics.” This video focuses on the problems specific to the 104 engine, how to prevent trouble, and things you may not read about in the factory service manual.

NOVEMBER 2022 UDPATE:  Part 4 WILL NOT BE COMPLETED AS THE CAR HAS BEEN SOLD AS IS.  Please sell Helpful information below:

The first link is an article by Steve Brotherton. You might google him to get more tips on the M104 engine. He is considered very knowledgable.

http://www.continentalimports.com/ser_ic100345.html


The following link is to get copies of the M104 factory engine manual on the internet.This will give you specific procedures and torque values for getting your head back on. There are also inexpensive CD manuals on eBay, etc. on the M104 engine. Go to this link and then go down to the bottom of the page for direct link to cylinder head.

http://www.w124performance.com/service/Index/104/01General.htm

Total Run Time of this Video:  37:58

 



How to view this on-demand video:

Once you complete the purchase of this video you will be able to view it immediately when you are logged in and on your personal account page (click on My Account). The video(s) will show up under My Video Manuals. The video is NOT downloadable to your computer or mobile device, but you will be able to view it anytime, from anywhere and from any device as long as you have internet access and you are logged in to your account at mercedessource.com.

Important note: This video manual may or may not include all the information you will need to troubleshoot and/or repair your specific problem/s. Please read the full description carefully to determine if this video is applicable to your year and model and contains the information you are looking for. If not, please refer back to our "Solutions Finder" and enter your chassis number and the specific problem you are having to see if we offer a solution.

Related Products: