All new 2006 to 2013 V6 and V8 engine repair kits! CLICK HERE to view AlL.
Kent's procedure uses the factory recommended "drip tube method" but with a "twist." He has devised a way to get accurate and consistant IP timing results while trying to get the drip tube to drip at one drip per second exactly when it should!
While working on the fuel injectors of a 240D this week, Kent finally decided he had had enough. After 20 years of fighting those fuel injector return hoses he decided he just had to come up with a tool to make the job easier. 2 hours later the tool was designed and the prototype made.
Any time you are removing and replacing your fuel injectors you will need to change the return hose and the heat shield crush washers. If you don’t, you will have leaking hoses and possible compression leaks at the injector nozzles.
If your fuel level gauge is not reading accurately or the needle jumps around and or your car’s low fuel warning light does not comes on, it is usually a problem with the tubular sending unit in the fuel tank.
If you think CIS fuel injectors can just be ignored, think again. Sure, your gas engine will continue to start and run “ok”, but you may find that it is not producing the power it once did nor the fuel mileage it once delivered.
Works on all models from 1977 to 1993 with the Bosch C.I.S Fuel Injection system - see models listed below: Now you can do it yourself on the bench with this inexpensive tester- Save big $$. Ever wonder how well your old CIS fuel injectors are working?
The timing device installed in the W115, W116, W123 and early W126 with OM615, OM616, and OM617 engines from 1986 to 1985 is somewhat a mystery to many owners.
If you are new to older Mercedes diesels and have not worked on them before, this is one of the first things you want to learn. Especially if you ever run out of fuel. Without knowing how to do this you will never get the engine started again!
For all MBZ diesel engines 1950 to 1999. Designed by Kent Bergsma. These are built at Mercedessource to control quality and production demands. Each one is tested here in our shop before shipping.
FITS all 116 123 Diesel and Gasoline, and 126 chassis from 1977 to 1985. Finally a socket to remove your fuel tank screen that really works. Most correct size sockets tend to be SO BIG that they require 3/4 inch drive ratchets and extensions to use them. Who has those in their tool box??
This is the actual set you will receive. Cleaned and inspected and ready to install.
Kent shares with you 3 key steps that you should consider doing to get your old fuel injected 6 and 8 cylinder engines running properly. These include:
In this 9-minute instructional video, Kent explains how to set up his injection pump cleaning and testing kit ( available separately ), and use it to clean out old fuel injection pumps of gum and grime, and then how to test them to make sure they are delivery fuel through every line.
This is the best way to determine if the expensive injection pump is going to work for old 4 AND 5-cylinder diesel engines that have not run in years. Watch the video below to understand what this kit can do.
Excellent quality zinc plated hose clamps as shown. These can be tighten with a straight blade screw driver or a 7mm socket or nut driver.
After completing the pressure test on your CIS engine, you discover a problem. But how can you find out how to isolate and fix it? This is going to require some research on your part. Start by learning how the system works and how each component plays a part.
In this video, you will see how the gauges are hooked up to a 560SL and how the pressures are read. The length of this 30-minute shows the detail Kent has put into filming all the critical components of doing a KE-Jetronic fuel system pressure test.
This video is specific to K- jetronic fuel-injected engines from 1976 to 1985. This includes the 350, 450, and 280 engines in the R107, W116, W123, and early W126 gas Mercedes. In this 29-minute video. Kent will show you how to hook up the gauge, run the fuel pumps, and complete the test.
There are a few factory recommend procedures and tests you should do before you do an actual pressure test on a CIS fuel-injected engine. In this 20-minute training video, Kent will walk you through these procedures step-by-step.
To do proper system testing on CIS fuel injection, you must find a way to get the fuel pump or fuel pumps to run continuously without the engine running. This can not be done by just using the ignition key. In this 15-minute training video, Kent will show the options available to do this.
This video will help you decide if you want to try to do a fuel pressure test yourself. It is a fairly simple DIY job but will all the confusion and misinformation on the internet; one would believe it is a complicated process that is hard to understand.
If you own or are restoring a CIS fuel-injected Mercedes, a pressure tester is a must-have! This complete kit will allow you to do it yourself with complete instructions. Why buy a tester that you do not know how to hook up and may not even be accurate?
Excellent used delivery valve(not scored) and housing nut that mounts on the top of the injection pump. Includes threaded housing, spring, valve body, and valve. A bad delivery valve or valves can cause rough idle, smoke, poor power etc.
This can do amazing things for your new fuel hose installaton on your old Benz engine. Watch the video to learn more. Sold individually in approximately 6 inch lengths.
If you are removing and replacing your M110 fuel injectors these are the seals you should have on hand. Always replace the rubber seals. I know it is possible to reuse the plastic sleeves but many times they are brittle and will be damaged upon removal.
In this 9 minute instructional video, Kent will explain how to test your fuel accumulator to determine whether or not it has failed internally. A failed accumulator will make your engine hard to start when hot.
In this 26 minute instructional video Kent will show you how to hook up a CIS fuel pressure tester to your older K-jectronic gas engine.
This xx minute video will take you step by step through the process of modifying your warm up regulator so you will be able to easily make adjustments to your cold start control pressure.
Before you make this modification you should be very familiar with the function of the WUR and how its pressure adjustements affect the performance of the K-Jetronic fuel injection systems. The tools and supplies offered in this kit will allow you to modify your warm up regulator at home and it y
New Mercedes o-ring as shown. Always replace this seal when removeing and cleaning your fuel tank strainer ( screen ).
This 16-minute video will instruct you on how to replace the fuel injectors in your 6 cylinder M110 safely and efficiently. Since this is a fairly straight forward remove and replace this is not a step-by-step video.
This is every thing you need along with free video instructions by Kent Bergsma. Why change the K-jet fuel injectors in your M110 engine. One thing is they are very old. Second this is right now they are readily available and resonably inexpensive.
We modify this wrench right here in our shop. If a picture is worth a thousand words, what is a video work. Watch the following for a full explanation.
You would be amazed at how much fuel can leak out of a fuel hose when you disconnect it from your tank or engine. This is an easy way to prevent messy spills.
When “rebuilding” an old Bosch mechanical fuel injector, replacing the nozzle is usually enough get it working again at peak performance. But sometimes you will run into a fuel injector that just won't fire right nor product a correct fan spray pattern.
When “rebuilding” an old Bosch mechanical fuel injector, replacing the nozzle is usually enough get it working again at peak performance. But sometimes you will run into a fuel injector that just won't fire right nor product a correct fan spray pattern.
It has now become essential that you replace this filter screen on these old cars, especially if they have been using gasoline with ethanol in it and the car has sat or sits for long periods without running.
Did you hear these are not available? No part number anywhere? Well, as the source we went to work and made it happen. You can now purchase the correct copper sealing rings for your OM616 and OM617 injection pump delivery valves.
This hose assembly was used on the fuel delivery systems in the late 1970s and early 1980s. Installed on some R107 450SL and 450SLC, W116 450SE / L and 280SE, and the W123 280E and 280CE. Be sure to check your car before ordering to make certain this hose is installed.
Those old hardened and discolored plastic fuel hoses in your diesel engine compartment probably need to be replaced. When they crack and break you can dump a ton of fuel out on the road before your engine quits and leaves you stranded.
In this 13-minute video instruction Kent will show you how to make your own accumulator tee hose connection either using parts from. our kit ( see below) or parts you purchase yourself. This video is included free with the purchase of our kit.
This kit will give you everything you need to fix the leaking or aged Tee hose between the fuel damper and the fuel accumulator on most 1977 to 1980 fuel delivery systems. Watch the video below to learn why this is needed.
Kent will take you over to his workbench and completely take apart a rusty and old fuel delivery system from a 1980 450SL and put it all back together again with some shiney new paint and parts supplied in his special kit for these cars. This video runs for 24 minutes.
It was difficult to find a filter to fit the correct size outlet hose. Install this steel 10-micron filter in your fuel tank outlet hose to protect your fuel pump. Clamps are provided along with a pull to plug the fuel hose temporarily to reduce fuel spills.
This on-demand instructional video was filmed to go with Kent's new fuel tank sending unit service kit launched in June of 2020. This is not a complete video on the subject of fuel level sending units. For the complete video see related products below.
If your fuel gauge stops working or is not reading accurately, many times it can be repaired by removing it from the fuel tank, taking it apart and giving it a good internal cleaning of the contact points, float shaft, and wires.
In this video, Kent will show you how to safely and cleanly remove the fuel from the tank on your older Benz. You will need to drain the fuel anytime you replace the back end hoses, the tank filter screen, the fuel pump or the fuel filter.
Works on the following: 6 cylinder gas MFI engines 1959 to 1972, 6.3 and diesel engines 200D 220D 240D 300D 300TD 300CD and 300SD through 1985.