W116 300SD Trunk Emblem and Handle Set - USED
Excellent set of emblems as shown. Very good chrome.
All new 2006 to 2013 V6 and V8 engine repair kits! CLICK HERE to view AlL.
Excellent set of emblems as shown. Very good chrome.
NEW quality aftermarket part. Fits late 123 240D 300D 300CD 300TD 1980 to 1985. Use your existing motor
This is a very common wear item on high mileage 126 chassis. It will start out as a clunking noise when you go over rough ground. When real bad it will be hard to get your car to track right down the road (it will want to wander) and you will experience rapid and uneven tire wear..
For all 201 chassis 190E and 190D built from 1984 to 1993. The PDF download repair guide will take you through the process of how to properly remove your heater blower motor and replace the motors two brushes. This is the most common reason for failure.
Fits 126 years 1986 to 1991
Brand New Rotors as shown. You will receive 2 fronts as shown. Fits all 126 Chassis Gasoline and Diesel, from 1986 to 1991.
Specifically 300SDL 300SE 300SEL 350SD 350SDL 420SEL 560SEL 560SEC.
GOOD USED air filter housing as shown. Study the picture carefully. This is the actual unit you will receive. A BRAND NEW filter is included. This includes the rubber flex elbow to the turbo, but some of the top breather hoses are missing.
Buy the tools with the variety pack of LED dash bulbs and save $$$. You will receive video instructions on how to use the tools and how to change the bulbs. Click on each of the related products below to read a full description of what is included in this kit.
Made in the U.S.A. This little electric heater has a strong magnet to stick to the bottom of the steel pan and a long cord to reach a 110v outlet. It is rated at 180w. It can reach 400 degrees so do not touch it when plugged in.
BONUS: Free video instructions included. These bulbs have been fully tested by Kent to work correctly in older Mercedes instrument clusters. Be careful using other brands of LED bulbs in the W123, w126, and W201 instrument clusters, as some can burn up your circuit boards.
Books average 65 to 80 pages in length. Lots of good schematics and troubleshooting and testing info.
For 1973 owners: make sure your cap matches the one in the picture ( all orange). Wires are soft and flexible. You can see very little wear inside the cap.
This Supplement Service manual for engine 102.983 highlighting the differences between the 16-valve engine from the standard 8-valve engine.
Good quality tool with strong magnet. Extension is approximately 10 inches long.
For 1990 to 1995 W124, W126, R129 and W140. Does NOT fit W201 190E.
PLEASE NOTE: 12mm long and short bits have been removed. Special Price
These are rare and very collectible for the performance enthusiast. Each book contains the following: IIS
Here are the titles, dates of printing, and total pages in each of these four factory training booklets. IIS
Originally this was a two-book set. The larger book covered all things related to the 190 Ponton. Most mechanical components were the same between the sedans and the SL. The supplement manual covers those things related specifically to the SL - body, top, twin carbs, etc.
It seems like you never needed a 16mm or 18mm wrench or socket until 1996. After the intro of the W210 things changed. This set of 3 quality U.S. made tools consists of an 18mm stubby combo, an 18mm deep 3/8 drive socket, and a 16mm short 3/8 drive socket.
This the exact puller you will receive. Handy for small jobs.
This Introduction manual is intended to familiarize technical personnel with the Registration year 1976 Passenger Cars. This covers changes and new developments, it does not cover all repair information on the included chassis. 87 Pages
This Introduction manual is intended to familiarize technical personnel with the Registration year 1974 Passenger Cars. This covers changes and new developments, it does not cover all repair information on the included chassis.
This introduction into service for the year 1973 introduces the W 116 Models: 450 SE (116.032) & 450 SEL (116.033). Manual Contents: General Description of vehicle components, Assembly, inspection and adjusting procedures, Testing and Tuning Data, Maintenance instructions, tools and Equipment
I can now offer a unique digital meter and several attachments in a convenient carrying case that I can grab and go with anytime. Are you tired of fussing with your standard meter straight-tip probes? I think they are worthless.
Kent was a little skeptical when you first used this—it sounded like it would be too good to be true. The first use was getting some rusty bolts off the Garrett T3 turbine housing ( some of you know the pain there!). Well, it worked, and it worked very well.
Very nice set with silicone copper core wires. See detailed pictures below. Two coil leads of different lengths included. Check before ordering as this fits these models from the early 1990s with dual distributors in the front of the engine. 400E. 400SE.
It is really frustrating when you doing a job on your Benz and find it needs a 16mm or 18mm tool and you don't have it. Most of the older sets of wrenches and sockets did not include these two sizes. Just before and after 2000 Mercedes started using more of these size nuts and bolts.
Quality aftermarket part. If over 80,000 miles, replace this part when you replace your serpentine belt. Kent's custom tensioner tool is available separately below to help make the install of this new tensioner a "snap."
If you are looking for a way to really beautify your classic Benz engine compartment this could be it. These hardly ever get changed and most are stained and ugly. This is a genuine OEM part with rubber seals included. MAKE CERTAIN yours matches in size and shape before ordering.
Good used set of valves for OM617 turbo cylinder heat. Includes all parts as shown (valves, springs, rotators, and spring caps. 10 THIN adjusting nuts INCLUDED. No valve cap nuts. Only parts shown in the picture are the actual items you will receive.
LAST SET WE HAVE. Best you can get for your 300SEL
FREE steel liner included as shown. Brand new old stock. Size on top of piston is 91.47
This is one of the nicest I have seen both inside and out. Complete with the attachment through the rear glass hardware. Kent will also include at no extra charge his on-demand video on restoring one of these. This will show you how to remove and replace it in your wagon.
Fits all Mercedes models with the 14" Alloy bundt cake style wheels. The measurements are M12x1.5mm by 51mm overall length. This is a set of five USED wheel bolts that are not all rusty.
Great find, especially if you are a W111 coupe convertible enthusiast. This introduction manual is intended to familiarize technical personnel with the W109 and W111 series vehicles and the M116 V8 engine.
This 17-minute video will cover the removal of an old Hirschmann power antenna and then Kent will show you how to troubleshoot the wiring plug in the car to see if you are getting proper power back to the antenna. No sense in replacing a faulty antenna until you make sure your wiring is OK!
In this 30-minute instructional video, Kent will walk you through the steps to remove your old antenna, test and troubleshoot your wiring plug coming to the antenna, and install our aftermarket antenna using the special wiring connectors we include in the kit.
This will hold the top of the strut and keep it from turning when removing and installing the 22mm nut.
Hard to believe we took so long to come up with this tool. It was Gerson's genius that made it happen. The secret turned out to be the hook that keeps the tool in place while stretching out the rubber donut. Wow! What a cool tool.
Damage-free 108 front fenders, front bumper, rear bumper, hood, and trunk lid These parts all came off a 1968 low mileage 280S that sat in a warm garage since 1978. This happens to the parts on an old car when it never leaves a warm garage for 40 years! Sorry, we can not ship them.
BRAND NEW OE breather parts as shown. Make sure these match the ones on your W201 190D before ordering. Includes breather tube and new valve cover seal.
Brand new passenger side rear door power window regulator. Motor not included
Fits the following 126 models:
New RIGHT FRONT door seal on 4 door sedans only. Only seal shipped. No clips or instructions.
If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.
Fits all 123 240D 300D 300CD 300TD 280E 280CE 1977 to 1985. This is a good used rear bumper rubber. There are no gouges or tears, only some slight scratches in places. The rubber trim piece that goes over the bumper shock mounts is in very good used condition.
New Factory reproduction of original owners handbook. Excellent condition.
This is an original first aid kit. It came out of a 1981 300D. Contents look mostly complete and are original. I have 2 so it may or may not exactly have everythings inside as shown below. It probably should not be used as a first aid kit. This should be for original cosmetic purposes only.
Very Good used trunk emblems and star as shown. They are very straight and plating is bright. The handle has one very small ding in the bottom center.
Fits the following: All 116 123 and 126 Chassis Diesels from 1977-1985. This is a brand new Genuine Mercedes Steering lock vacuum valve that is located on the back of your ignition lock assembly. We include 2 pieces of correct sized rubber vacuum hose as shown.