If you own or are restoring a CIS fuel-injected Mercedes, a pressure tester is a must-have! This complete kit will allow you to do it yourself with complete instructions. Why buy a tester that you do not know how to hook up and may not even be accurate? We only give you what you need for Bosch K- jetronic and KE-Jetronic tested to eliminate confusion. And with the six-part video series included you will learn how to hook this up and make the tests YOURSELF!
Product Details
IMPORTANT NOTICE: There is a difference now from what you will see in Kent's video. NO MORE QUICK DISCONNECT. If the internal seal fails it will leak a lot of fuel. So the hose is now connected directly and clamped to the T-fitting. This will eliminate the potential for any fuel leaks.
Free thin 14mm wrench included:
We also have a short DIY build kit for this tester. See related products below.
Related Products:
1976 to 1993 CIS Fuel Injection Pressure Tester Partial "Short" D.I.Y Build Kit
If you own, plan to own, and want to enjoy driving your old CIS fuel-injected Mercedes, Kent highly recommends you learn to do a full fuel system flow and pressure test.
Super Thin 14mm Combination Wrench for CIS Pressure Tester Fittings
When pressure testing your KE-jetronic fuel injection, you may find you need a really thin wrench to install the small fitting on the right side bottom of the fuel distributor.
Fuel Pump Relay Switch Jumper Lead (s) for Pressure Testing K and KE-Jetronic Fuel Injection
PLEASE NOTE: Wire color may be all red or all black (depending on stock on hand) Performing some fuel pressure tests on your K-jet or KE-jet engine
KE-Jetronic Fuel Injection Troubleshooting Multimeter w/ Special Attachments
This high-quality meter can test all types of automotive electrical circuits, but Kent has discovered it is particularly well suited for testing Bosch KE jetronic fuel injection components on those CIS models from 1984 to 1993. Extra adapter fittings are included as shown.
1976 to 1993 C.I.S Fuel Injection 6-Part Video Training Seminar
It has been over 30 years since the last Mercedes with Bosch C.I.S. fuel injection was manufactured. If you own a 1976 to 1993 Mercedes gas engine with this type of fuel injection, you may have difficulty finding someone to work on your car. In some parts of the country, it may be impossible.
Bosch CIS Training Series 1: What’s Needed to Test K-Jet and KE-Jet Fuel Pressure
This video will help you decide if you want to try to do a fuel pressure test yourself. It is a fairly simple DIY job but will all the confusion and misinformation on the internet; one would believe it is a complicated process that is hard to understand.
Bosch CIS Training Series 2: Options to Get Fuel Pumps to Run with Engine Off
To do proper system testing on CIS fuel injection, you must find a way to get the fuel pump or fuel pumps to run continuously without the engine running. This can not be done by just using the ignition key. In this 15-minute training video, Kent will show the options available to do this.
Bosch CIS Training Series 3: How to Do Preliminary Fuel Flow and FD Leak Tests
There are a few factory recommend procedures and tests you should do before you do an actual pressure test on a CIS fuel-injected engine. In this 20-minute training video, Kent will walk you through these procedures step-by-step.
Bosch CIS Training Series 4: How to Hook Up and Test K-Jetronic Fuel Pressure
This video is specific to K- jetronic fuel-injected engines from 1976 to 1985. This includes the 350, 450, and 280 engines in the R107, W116, W123, and early W126 gas Mercedes. In this 29-minute video. Kent will show you how to hook up the gauge, run the fuel pumps, and complete the test.
Bosch CIS Training Series 5: How to Hook Up and Test KE-Jetronic Fuel Pressure
In this video, you will see how the gauges are hooked up to a 560SL and how the pressures are read. The length of this 30-minute shows the detail Kent has put into filming all the critical components of doing a KE-Jetronic fuel system pressure test.
Bosch CIS Training Series 6: Finding Follow-up Information to Help Interpret Test Results
After completing the pressure test on your CIS engine, you discover a problem. But how can you find out how to isolate and fix it? This is going to require some research on your part. Start by learning how the system works and how each component plays a part.
How to Test the EHA Valve on Bosch KE-Jetronic Fuel Injected Engines - On Demand Video
In this 13-minute CIS training video, Kent will walk you through the steps recommended by Mercedes Benz to fully test the operation of the EHA valve on 1984 to 1993 4, 6, and 8-cylinder engines with KE-jetronic fuel injection.