All new 2006 to 2013 V6 and V8 engine repair kits! CLICK HERE to view AlL.
This quick reference guide will help you locate the source of the most common problems found on 123 and 126 chassis front suspensions. Illustrated parts breakdowns will guide you to the parts needed to repair the problem.
Fits 126 Chassis 1981 - 1991 EXCEPT 560SEL. The best way to restore the original ride and feel of your Mercedes is to replace your shocks with new Bilsteins. There is no other shock that will perform as well. These are OEM COMFORT shocks that give you the smoothest ride.
Fits all models list below without Self Leveling Rear Suspension. The best way to upgrade the original ride and feel of your Mercedes is to replace your shocks with new HEAVY DUTY Bilsteins. There is no other shock that will perform as well.
This is a very common wear item on high mileage 126 chassis. It will start out as a clunking noise when you go over rough ground. When real bad it will be hard to get your car to track right down the road (it will want to wander) and you will experience rapid and uneven tire wear..
This is a common wear item on high mileage 126 chassis. It will start out as a clunking noise when you go over rough ground. When real bad it will be hard to get your car to track right down the road (it will want to wander) and you will experience uneven and rapid tire wear.
Fits the Following: All 123 and 126 Chassis from 1977 to 1991 .
This 16 page PDF downloadable SLS manual was written specifically for 123 300TD wagon owners, but also applies to the models mentioned above, 300TDs from 1979-1985 and other chassis above up to 1990.
This is a very common wear problem on most older Mercedes. The steering idler arm bushings are made out of rubber and when they wear your steering will get sloppy and you may hear squeaking noises when you turn the steering wheel.
In this short 3-minute video, Kent will show you a trick that few know about. You can get those tapered shaft ball joints ( like to find on tie rods and control rods) loose without damaging the rubber boot. It can be faster and less painful than using traditional methods.
You must inspect the sway bar, especially if the car has been subjected to road salt. Kent will explain in more detail in the video below.
Forget about this bolt rusting again on your sway bar. Included are 2 correct bolts and blue thread locker to secure them in place.
For one side only. It saves 20 hours of labor not having to replace the sway bar.
Do you want the rear end to ride like a new on your later 126 sedan or coupe? Then you have to replace the key suspension rubber parts that attach the rear suspension to the car. This kit has the parts you need, but it does not include instructions.
Do you want to make the rear end ride like a new R107 - Then you have to replace the key suspension rubber parts that attach the rear suspension to the car. This kit has the parts you need. No instructions.
Kits contains:
These are the forward trailing arm bushings that connect the arms to the rear subframe. When these bushing get old or start to crack and break apart, you may hear noises in the back and the rear end may want to steer the car on its own.
Flushes Out Old Grease and Repacks Bearings with Less Mess. This Handy Packer works on bearings up to 3 1/2" O.D.
This high pressure hose is a common leak area on the 126 gasoline V8 models. If you see oil drips just aft of your power steering pump it is probably this hose.
This is a short addendum to the full instructions on resealing an SLS hydraulic pump. This will now be included with the reseal kit. Disregard the old method mentioned elsewhere
In this detailed 30-minute video Kent will walk you through the process of installing new tie rod ends on his 1959 Mercedes 220SE. The principles are the same on almost all models from the 1950s up to the 1990s. He will explain the differences in adjustment between the older and newer styles
Loose steering or wheels shaking at speed. This can often be worn out tie rod ball joints. The joints can be replaced as a DIY project. Watch the video below to see if this is something you want to take on yourself.
This kit includes:
Fits all Mercedes models with the 14" Alloy bundt cake style wheels. The measurements are M12x1.5mm by 51mm overall length. This is a set of five USED wheel bolts that are not all rusty.
In this video, Kent will show you how he fixed his leaking tires on his chrome alloy wheels by using Miracle Paint. This is a full 22-minute step-by-step instructional video. Watch the video "trailer" below to give you a better understanding of what is involved in this procedure.
Kent will get right up behind the rear end hub plate and show you close up how to remove and replace a sway bar link. This is not a difficult job especially if you follow the sequence shown in this 7- minute video.
In this 30 minute-long video Kent will walk you through what he did for the rear suspension on his 1983 240D.
A brand new set of two grease caps as shown by Febi. Time to get rid of those ugly beat up and dented grease caps.
Socket is now black (impact grade). This is a tool that Kent first thought about making 20 years ago. While installing shock absorbers in his 380SL he had finally had enough - so it was back to the machine shop to come up with a new tool.
This on-demand video will take you through the process of replacing the worn-out ball joint bushings that connect to the front suspension guide rod on all W126 sedans and couple built from 1980 to 1991. This video comes free of charge when you purchase our complete repair kit.
This is our complete kit for an at-home DIY repair. Loose and worn out guide rod ball joint bushings are the most common front suspension problem on the W126 sedans and coupes. Check the condition of yours if you have not recently done so.
This video will cover the use of my custom plastic tool to safely remove the steel center section for the outside aluminum housing with rebuilding your older style SLS ( Self Leveling Suspension) hydraulic pump. No other instructions included here.
These are the 4 long bolts that need to be removed when changing your W126 brake rod control joint on your front suspension. There are two on each side. They do not come in the repair kit so if you bolts are very rusty you might want to have these new bolts on hand before you start your repair.
This rubber part fits all W126 sedans and SEC coupes from 1980 to 1991.
In this video, Kent explains the correct procedure for cleaning and lubricating your hubs and rear brake rotor BEFORE you install your wheels. He hardly ever sees this done when removing wheels on 15 plus-year-old Mercedes so he knows it is almost ALWAYS neglected.
PLEASE NOTE: These are not complete instructions on how to open up an early style SLS pump and properly reseal it. Rather, these are some tips that will make the job go faster and easier. These are things Kent has learned rebuilding a number of these pumps himself.
This long bolt washer are is available new. When replacing the Brake Control Rod Ball Joint Bushing on the W126 chassis this long bolt has to be removed. If severely rusty you may have to cut off with saws all. The long bolt is not included in the repair parts kit.
I do not need to say much about this tool. Well made and well thought out. Someone who obviously was frustrated at scratching the finish on his or her alloy wheels came up with this idea. Watch the video below to see why this is now my favorite go it 17 mm lug bolt socket.
This U.S.A. made 17 mm 8 inch long combination wrench is custom modified here in our shop to help you easily install Bilstein front and rear shocks on most of the older model Mercedes Benz.
In this video instruction, Kent will demonstrate how to check for one possible source of a mysterious front end clunking sound. Any clunking noise you hear when driving over rough ground or when braking should be investigated immediately.
In this long video manual Kent will walk you step-by-step through the process of removing the older square style leveling valve from your Mercedes, opening it up without losing the spring and balls, removing the old o-rings and cleaning the parts properly, installing the new o-rings, and putting
Trying to fix a rough or bouncy ride in your SLS Mercedes? Not sure what is causing the problem? Maybe you have heard that it might be the accumulators.
In this video Kent will walk you through the procedure of removing the old accumulators and installing new ones in a W123 300TD wagon. It is a very straightforward job that only takes a couple hours. You will need to raise the car and safely support it on jack stands.
NOTE: UPS GROUND SHIPPING ONLY. This complete kit will help you flush the old ATF fluid out of your power steering system and replace it with new high-performance power steering fluid.
If you have a 1985 or older Mercedes Benz it is time you flush that old automatic transmission fluid out of the system and replace it with a good power steering fluid. ATF formulations have changed over the past 20 years.
When replacing the front upper control arms you formost need to think about safety. You will need a good quality and large rolling hydraulic floor jack, and a couple good jack stands.
This video instruction will walk you through the step-by-step procedure of how to do a "service" on your power steering system.
PLEASE NOTE: UPS GROUND SHIPPING ONLY. Sorry, no postal, expedited or international shipping. This is a highly neglected maintenance item on older Mercedes Benz. If you want to prolong the life of your steering box and power steering pump here's how.
UPS GROUND SHIPPING ONLY. DO NOT order postal or expediated. International shipping not available. If your fluid is old and dark it is time to flush it out. 1986 to 1999 model W126, W201, W124, W140 and W126 with SLS have a smaller tank than the earlier models.
New O.E. filter as shown. See related products for fluid and flushing instructions. This is VERY easy to inspect and change yourself.
This instructional video covers the procedure for flushing the old hydraulic fluid out of an SLS system and installing new fluid. The example shown in this video is from a W126 560SEC.
Digital 4 page PDF instructions. Detailed pictures and step by step instructions to assist you in completing the suspension guide rod bushing replacement.
Brand new rear end differential front seal. Fits both gas and diesel models. This is NOT the seal for the axles.