All new 2006 to 2013 V6 and V8 engine repair kits! CLICK HERE to view AlL.
ONLY ONE AVAILABLE. Very good used working Bowden cable with good plastic threads on the adjuster. No longer available new. Approximately 20,000 miles since new. This will not fit the 1985 transmissions with the black modulator.
If your modulator is working ok, but leaking transmission fluid, you may only need to replace the inexpensive oring ( o ring ). You do have to be careful when removing the modulator from the transmission. For instructions (available separately) see related products below.
Transmission service on these older Mercedes is very often neglected and it is something you can do yourself. It should be done every 30,000 miles or every 5 years (whichever comes first). After you watch this video you will find out why you should do it yourself!
In this 5 and a half minute video Kent will show you how to replace the o-ring seal at the base of the dip stick / fill tube going into the automatic transmission case on the right side.
This is becoming one of the common transmission fluid leaks on these older automatics. If the trans is leaking fluid in small puddles while the car sits for longer periods suspect this seal. You can be fooled thinking it is coming from the pan gasket.
Custom ordered for a better fit than original! special Oring seal for the bowden cable housing where it connects to the right side of the automatic transmission. This is a common leak area and you may be fooled into thinking it is leaking out of the pan gasket.
Illustrated 6 page step-by-step instructions for proper removal and installation of the modulator upgrade for the years and models noted here. Includes how-to specific details for using the new adjustment cap on the upgraded OEM modulators now available. These are installation instructions only.
The bowden cable runs from the transmission to the throttle linkage on many Mercedes from the early 1980's up through the early mid 1990's. When this cable fails or is out of adjustment the transmission will either shift too early or too late.
The plastic shift bushing is a very common part that needs to be replaced on older Mercedes. Can you believe it is the exact same part that was used on all models for over 25 years! It is an inexpensive part that can cause big problems if it breaks out.
If you have ever tried to remove and reinstall a shift rod attachment clip under your Benz you know how frustrating it can be.
I have received so many emails on this topic that I had to sit down and write a very detailed manual over 130 pages in length! Let's face it! Diesel automatic transmissions can be troublesome, particularly those models that use vacuum to control shifts.
INCLUDES TRANSMISSION PEAK TUNING MANUAL. DO NOT ORDER SEPARATELY
This unique kit will allow you to hook up a 30 in HG vacuum gauge between your vacuum control shifting valve (VCV) and your transmission modulator to test the VCV for proper function and to tune it for peak shifting performance.
Applicable to 114 115 116 123 and 126 Chassis, years and models listed above. Troubleshooting an annoying shift problem must first start with the vacuum modulator.
I don't think there is any owner out there who has owned a 1978 to 1993 diesel automatic for any length of time and who has not had some sort of shift problem with the transmission. Maybe it was just a little jerk or a slipping shift. Maybe the rear end clunked hard when you came to a stop.
If your transmission is shifting too soon it can really rob your car of power and acceleration. If it is shifting too late it can be very loud and annoying and even affect fuel economy.
If you are experiencing very hard or less than perfect shifts, a failed transmission modulator could be the problem. New Genuine Mercedes part. This unit is an upgrade over the original. It has a better thrust pin design which is less prone to cause pressure variations in cold weather.
Often not done, but you will regret not adding this correct SACHS grease to you clutch input shaft splines! Regular grease with not stand up over time.
A high quality bearing. It is a good idea to replace this anytime you have the transmission. Remember it spins a lot!
In this 24-minute instructional video, Kent shows you more than just how to change the transmission filter and the pan.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
Yes, YOU can fully drain all your transmission without using any type of "power flush." Full detailed video instructions are included. This kit is easy to connect and the process is quick and clean. Watch Kent's YouTube video below for full details.
In this 15-minute video, Kent will show you step-by-step how to safely remove the Bowden cable without damaging it and how to install it to get the proper connection. This is not as easy as it looks, and you can break it if you are not careful.
Kent is a firm believer in using these strong magnets inside a transmission pan to help extend its useful life.
They should be placed toward the rear of the pan as shown in the picture below.
These transmission pans get "out of shape" due to over-torquing the bolts. That crushes the stops (see below), and when that happens, it is very hard to get the pan seal not to leak. Your best option if you are doing a transmission service is to replace the pan.
Also works on 380SL and 560SL transmissions. Before you think you can easily remove the Bowden cable from the transmission, watch the video below.
These transmissions are now 40+ years old, and with age comes hardened o-rings and seals, leading to what I call "pesky" leaks. They are not bad enough to flow on the ground, but they do leave wetness around the transmission and drips on the garage floor.
These transmissions are now 40+ years old, and with age comes hardened o-rings and seals, leading to what I call "pesky" leaks.
If your clutch is making growling noise when you push the pedal in these are the parts you need to fix it. You might want to consider replacing the pressure plate and disc while you have the transmission out.
In this 17 minute instructional video Kent will walk you through removing and installation a VCV valve off the back of the injection pump and the proper way to adjust the linkage travel for best performance. A number of tips will be shared to reduce frustration and prevent problems.
Clear instructions on how to remove the old boot and install a new one. Total run time:
This was a new replacement unit only on the car for about five years before the 1980 transmission was removed. RED MEANS RED. Only works if your current transmission has a red modulator THAT LOOKS EXACTLY LIKE THIS ONE. Will also work on some 80-81 W123 240's.
This guide will explain how to properly change the fluid and filter in your late 123, 126, 201, 124, late 107 chassis Mercedes as well as early 129 and 140 chassis. This includes model years from 1982 to 1993.
Brand new gasket. Make sure this fits your transmission before ordering. No returnable if ordered in error.
Common wear item. Check for looseness where they nylon bushing sits in the aluminum connector. This is a brand new Shift rod Metal Connector with Nylon Bushing installed. Sold individually. List price $20.00
New rubber mount that bolts on rear of transmission. Failure of this part can cause excessive engine vibration. Common failure item. Fits models listed above. NO INSTRUCTIONS INCLUDED. Single mount only no bolts or nuts included.
This is the absolute best gasket maker when you have a clean and tight metal to metal contact. Examples of where you would use this is SEALING the rear differential cover, aluminum oil pan where is mounts to the engine block, etc.
Good used flywheel stretch bolt as shown. Very limited stock. Torque converter flex plate bolts.
Getting to and removing the two hex head bolts that hold the starter to the bellhousing can be a real test of your sanity - especially if you don't have the right tool! You will need a heavy duty hex socket on a strong wobble extension.
Set of (2). The number one cause of a loose or rattling shift lever is failed or missing shift lever bushings. Our upgraded bushings are made out of nylon and are much tougher than the original plastic type. No instructions or special tools included.
This is the most complete front reseal kit on the market today. It includes Kents new IMAGE-BY-IMAGE instructions. That means there is an image for every single step in the operation of replacing these 2 (Yes there are 2!) critical front seals.
Some of the most common auto transmission leaks on the early automatics come from the banjo bolts that connect the filler tube to the bottom of the pan and the two transmission coolers lines to the lower front transmission housing.
NEW Genuine Mercedes Modulator Cap. Check to see if yours is cracked. Cap removal is required for modulator adjustment.
Typical old and cracked rubber cap:
SPECIAL ORDER ONLY -- If you are going to pull your transmission to replace any clutch components you should do it right! That means to replace all key wear components so you don't have to remove the transmission again any time soon.
If you are going to pull your transmission to replace any clutch components you should do it right! That means to replace all key wear components so you don't have to remove the transmission again any time soon. Go with the best so the repair will last the longest.
If you have a leaking transmission seal it can be a real bear to get the old seals out without this puller tool. It works on both the front and rear transmission shaft seals. This tool also works great for removing the front crank seal on both gas and diesel engines.
Common diesel transmission leak source. These aluminum washers fit on each side of the banjo connection where the oil cooler lines bolt to the right and left front side of the transmission case. Fit 300D 300TD 300CD and 300SD with automatic transmissions from 1981 to 1985.
Brand new Auto transmission torque converter drain plug for All Mercedes, gasoline and diesel, from the late 60s up to the late 90s. If you are doing a complete transmission flush you will need to drain the torque converter. Good to have spare on hand!
New Genuine AT transmission pan. Fits most TURBO 123 and 126 diesels 1982 to 1987 with the exception noted.