Search | R129

Displaying 1 - 50 of 239
On Demand Video
Cleaning and Detailing a Mercedes Engine Compartment- On Demand Video Instruction
$4.99

Extreme Detailing Part 4: Cleaning and Detailing an Engine Compartment Safely - On Demand Video

Kent will show you how to get it super clean with minimal water and overspray

In this 14-minute video instruction, you will get to see how Kent cleans and details an engine compartment in a W210 E430 using his favorite chemicals and techniques. This includes using less than a gallon of water and controlling the spray rinse so you protect sensitive electrical components.

$99.75

Complete Lubrication Kit w/ Applicators in Carrying Case

Revised May 18, 2024 to now include Kent's Miracle Lube. This is your grab-n-go for all your lubrication needs on your older Benz

If you own and maintain an older car (especially 15 years and older) you must be willing to take care of its lubrication needs or you may spend big money later in repairs.

$26.00

W201 W124 Front Shock Strut Top Nut Special Wrench

Also works on R129 convertibles

When replacing the front struts ( shock absorbers ) on a W201 W124 or some W129 chassis it is frustrating and time-consuming trying to remove and replace the big 22 mm top nut on the front struts ( shocks ).

On Demand Video
$9.99

W201 W124 W140 R129 REAR Shock Absorber Installation - On Demand Video

Full step-by-step instructions including tools needed and special tips

In this video Kent will demonstrate how to replace the REAR shocks in the chassis mentioned above. He will do this on the ground on his W124 coupe using a floor jack, jack stands, and hand tools.

On Demand Video
$12.99

W201 W124 W140 R129 FRONT Shock Absorber Installation - On Demand Video

Full step-by-step instructions including tools needed and special tips to make the job go easier

In this video Kent will demonstrate how to replace the FRONT shocks in the chassis mentioned above. He will do this on the ground using a floor jack, jack stands, and hand tools.

$3.85

Windshield Washer Squirt Nozzle Cleaning and Adjusting Tools

2 wire tool set - One to clean and one to adjust - watch video below for details

Are you tired of windshield washers sprayers that done spray straight or don't spray at all. If you can hear the pump running but no fluid is coming out the nozzles it could be the nozzle holes are plugged with dirt.

$14.75

Hirschmann Power Antenna Mast Cleaning and Lubrication Kit

Extend the life of your power antenna by cleaning and regular lubrication

"I have heard some owners complain about the unreliability of those older Hirschmann power antennas. I would say that in at least 80 percent of the few hundred antennas I have taken apart that went bad - the reason was lack of lubrication!

$84.50

DELUXE Windshield Fine Scratch Removal and Glass Deluxe Polishing Kit w/ Power Tool

WARNING! Not guaranteed to work on all scratches. WILL NOT WORK ON SAND PITS. Do finger test on wiper scratches BEFORE ordering!!! Read and see more below.

Contains all supplies and video instructions you need - including a high speed power multitool to remove very fine scratches. Purchase together and save $$$$. Ever wish you could get rid of the annoying wiper scratches on your front windshield (or rear hatch glass if you have a rear wiper)?

$49.95

Windshield Fine Scratch Removal and Glass Polishing Kit

WARNING! Not guaranteed to work on all scratches. WILL NOT WORK ON SAND PITS. Do finger test on wiper scratches BEFORE ordering!!! Read and see more below.

Contains all supplies and video instructions you need - except a multitool (see description. )Ever wish you could get rid of the annoying wiper scratches on your front windshield (or rear hatch glass if you have a rear wiper)?

On Demand Video
$15.99

How to Remove Fine Scratches from Your Car's Windshield - On Demand Video

Video instructions using Kent's glass polish kit to remove scratches with less mess and less heat!

This video will take you step by step through the process of using our glass polish kit with a multitool to remove those fine scratches from your windshield or rear hatch glass. It also works great for polishing the water and acid rain out of any glass, including shower doors!

$8.95

Anti Corrosive Gel for Magnesium and Aluminum

For protecting clean and bare aluminum and magnesium engine parts

Kent has been working a long time to find a way to stop the ugly corrosion on aluminum and magnesium engine parts. Particularly valve covers and intake manifolds.

$32.75

1/4 Inch Drive Beam Type Super Low Torque Wrench

Very accurate for low torque settings - 0 to 9 Newton Meters or 0 - 80 inch pounds

If you are tired of "guessing" on those critical low torque settings maybe it is time to get a small torque wrench. This is the one Kent likes for super low torque settings up. It is quality made and will not cost you an arm and a leg. You can even calibrate it yourself!

$30.99

Gas Engine Spins But Won’t Start - Video Class with Kent Bergsma

Watch all seven videos in this series - and learn how to get your gas Mercedes starting and idling better.

Too many emails on this subject pretty much forced Kent to do this almost 3 hour long video class. If you are having problem starting your old 1976 to 1993 Mercedes with Bosch C.I.S. fuel injection this is a must see.

On Demand Video
$9.99

How to Use Kent's New Instrument Cluster Removal Tools - On Demand Video

Tips and tricks to get those stubborn clusters out of the dash

This video is free with the purchase of Kent's new dash cluster pull tool set. If you just want to see how he uses the tools and some tricks to get difficult clusters out you are welcome to purchase this video separately.  Approximate run time is 20 minutes.

$34.75

R107 W116 W123 W126 W201 W124 R129 W140 Instrument Cluster Removal Tools

With Free Video Instructions - For most models from 1972 to 1999

Removing a Mercedes instrument cluster from any of the chassis listed is easy with these special "pull" tools. Many owners do not realize that the instrument cluster is just pushed into the dash panel and not held in with any bolts or screws.

On Demand Video
Mercedes Muffler Repair - On Demand Video
$12.99

Center and Rear Muffler and Exhaust Pipe Replacement and/or Repair - On Demand Video

Common Rear Exhaust leak troubleshooting, component replacement and hole patching DIY techniques

How can you tell if you have a hole or leak in your exhaust system? What are the symptoms? Can the leak be patched? When will you have to get either a new center muffler or rear muffler or pipes or all three? Can you replace the mufflers yourself and what are the tricks?

$29.50

Custom Made Large Angled Head Clamping Tool

Multiple uses for hose removal, assembly, and holding parts safely for cleaning and polishing.

This is one of Kent's favorite tools around his shop. It is used almost daily. The tool rose out of a need to be able to safely hold fuel inectors while cleaning when with a large high speed wire wheel. No tool like this is availabe so it had to be built in our shop!

On Demand Video
$5.99

No Cost Steps to Fixing an Engine's High Idle Speed Problem - On Demand Video

Kent is always amazed at how often it is the simple things! You won't believe how easy it was to fix this engine!!

This video will be an excellent example of how to save big $$$ doing the work on your own car. If your gas engine is idling too fast in neutral it could be an expensive problem, but in many cases it is due to lack of maintenance over a long period of time.

On Demand Video
Mercedes Benz Impulse Codes - On Demand Video
$3.99

Read and Clear Check Engine Light Codes: 1988 to 1995 Mercedes - On Demand Video

Learning how to do this yourself could save you hundreds of dollars $$$$$$$$$

If you have a Mercedes of this era equipped with an impulse code reader you will find a little numbered black box similar to the one in the pictured here in your engine compartment. It is located over by the battery and may have a black cover on it that can be lifted off.

On Demand Video
Broken Radiator Neck - On Demand Video
$16.99

Repairing a Broken Plastic Upper Radiator Neck - On Demand Video

With the right products and procedures this can be safely done in most cases

Kent starts out the video talking about prevention by using the neck reinforcement kit he has been selling for years. In the case of his own 1990 300SL the neck had not been reinforced and it broke cleanly right in the middle.

$31.95

Plastic Radiator Broken Upper Neck Repair Kit

This will repair most cracked or broken upper radiator necks - Free video instructions

Another great solution from Mercedessource!

1978 to 1995 Mercedes only

A broken radiator neck can be safely repaired if it breaks off cleanly in the center or aft of the center of the neck. If it breaks off too close to the tank or breaks off in multiple small pieces then we advise that you replace the radiator.

On Demand Video
$14.99

M104 Gas Engine Head Gasket Replacement Part 3: Cleaning, Inspection & Parts to Order - On Demand Video

If you want your head gasket repair to last these are the important steps you must follow

The head has been successfully removed. There is quite a bit of work that will need to be done before the head is ready to go back on. The head and the block will need to be cleaned and inspected and parts will need to be ordered. Other parts should be replaced while the head is off the engine.

$79.95

2 Quarts of Miracle Paint with Spare Empty Pint Can

Cost saving option when tackling some major rust repair
If you are working on some larger rust areas or rust holes, you will probably need more than one quart to complete your project. This two-quart kit will generally cover and seal all areas if you are doing a rust cleanup on the underside of the car.
$2.95

123 107 126 201 124 722.3x and 722.4x Transmission Modulator O-ring Seal

For re-sealing green and black modulators on most 1981 to 1993 models.

If your modulator is working ok, but leaking transmission fluid, you may only need to replace the inexpensive oring ( o ring ). You do have to be careful when removing the modulator from the transmission. For instructions (available separately) see related products below.

On Demand Video
Under Body and Under Trim Spot Rust Repair - On Demand Video
$12.99

Under Body and Under Trim Spot Rust Repair - On Demand Video

High moisture "hidden" rust areas have to be treated and coated properly or they will not be permanent

On older Mercedes spot rust can be a hidden problem under side moulding trim, under fenders and rocker panels and inside the bottom edges of doors.

$32.50

Frozen Brake Caliper Piston Removal Pump Adapter Hose

Only works with Mercedessource Injector Pressure Tester - FREE VIDEO INSTRUCTIONS

This is a must-have if you attempting a caliper rebuild on one with stuck pistons. If you own one of our injector pressure testers here is a great add-on that will allow you to use the tester to remove stuck pistons from old brake calipers.

On Demand Video
Mercedes Brake Caliper Removal - On Demand Video
$6.99

Brake Caliper Rebuilding Part 1: How to Remove Frozen Pistons From Brake Calipers - On Demand Video

Part 1 of 3 Parts: For Mercedes brake calipers from the early 1960's to the late 1990's

You can save a lot of money if you can rebuild your old brake calipers, especially on some older models. If you can just get the pistons out of the housings, most calipers are rebuildable, unless they have been subject to road salt or have sat exposed to the weather for years without use.

On Demand Video
Code Reader On Demand Video
$13.99

How to Use a Scan Tool to Read Check Engine (Light) Codes - On Demand Video

This is way easier than you might think and learning how could save you thousands $$$

Enter the dreaded “check engine” light. When it suddenly comes on it can create fear and panic in many a driver. Kent has known some people who have sold their cars cheap because they just did not want to deal with taking the car into a mechanic to get it fixed.

On Demand Video
104 Mercedes Head Gasket Part 2 - On Demand Video
$12.99

M104 Gas Engine Head Gasket Replacement Part 2: Cylinder Head Removal - On Demand Video

A step-by-step procedure for properly removing the head from the engine

In this on demand video you will get to watch Kent remove the cylinder head from his 1990 R129 300SL with the 104 twin cam straight 6. This is a highly detailed video on how to do it without making the mistakes that many others have made. The job must be done with understanding and great care.

On Demand Video
104 Mercedes Head Gasket Part 1 - On Demand Video
$7.99

M104 Gas Engine Head Gasket Replacement Part 1: Overview - On Demand Video

Discussion of preparation, difficulty, potential problems and time it will take to do this job yourself

The primary purpose of this Part 1 introduction is to give you, the viewer an overview of some of the challenges you will be faced with if you decide to replace the head gasket yourself.

On Demand Video
Mercedes Overvoltage Relay - On Demand Video
$3.99

Solving Rough Idle and Low RPM at startup on a 1986 to 1993 CIS Engine - On Demand Video

Sometimes this can be fixed for very little work and money - but other times NOT..:-)

This is a common occurrence as these gas engines with Bosch C.I.S. fuel injection age. Most of them are now at least 20 + years old. The problem goes something like this. You start the engine cold and it will hardly run. It runs rough and idles very low and will even quit a few times.

On Demand Video
$9.99

How to Properly Install a Foam Hood Pad - On Demand Video

Kent shares all his tips and tricks to get the pad on straight, permanent, and looking good

If you are interested to see how easy it is to install a new hood pad, this video will let you see Kent demonstrate the process step-by-step. If you have purchased one of our hood pad kits, then this video can help you get your new pad lined up and installed properly. 

$42.95

24" Measuring Machinist Straight Edge with Protective Sleeve

A must have when working on engines.

When working on automotive engines a long heavy machinist straight edge is a must. This is the best way to tell if the mating surfaces are flat and true. That includes cylinder heads, engine blocks, intake and exhaust manifolds as well as critical sealing metal to metal covers and housings. 

On Demand Video
$12.99

CIS Gas Fuel Injector Removal, Cleaning and Testing - On Demand Video Manual

How to know for sure how well your gas fuel injectors are performing (1976 to 1993 CIS ONLY)

If you think CIS fuel injectors can just be ignored, think again. Sure, your gas engine will continue to start and run “ok”, but you may find that it is not producing the power it once did nor the fuel mileage it once delivered.

$249.00

CIS Gas Fuel Injector Spray Pattern Tester and Nozzle Cleaner

NEW VERSION 3 release.. See application notes below:

Works on all models from 1977 to 1993 with the Bosch C.I.S Fuel Injection system - see models listed below: Now you can do it yourself on the bench with this inexpensive tester- Save big $$.  Ever wonder how well your old CIS fuel injectors are working?

$19.95

HD Diesel Engine Glow Plug Circuit Tester

Every diesel owner should have one of these in the trunk to quickly test glow plug functions

A 12 volt test light is a very handy tool to have when working on any car but it is particularly important if you have a old diesel. This tool will allow you to quickly determine if there is power getting to your glow plugs, and if not where the power is breaking down.

$1.90

1982 to 1995 Auto Transmission Dipstick Tube Seal

Fits all models with the 722.315 and most 722.4 transmissions - see list below

This is becoming one of the common transmission fluid leaks on these older automatics. If the trans is leaking fluid in small puddles while the car sits for longer periods suspect this seal. You can be fooled thinking it is coming from the pan gasket.

$24.95

Main Dash Light Bulb Holder Socket Set

Great upgrade replacement for the weak W123 W126 W201 and W124 bulb holders. These are easier to turn with cluster still in the dash.

SOLD AS A SET OF TWO. You can watch Kent's video to see how important these bulb holders are and whey he likes them so much.

On Demand Video
Mercedes Ignition Switch Buzzer - On Demand Video
$2.99

How to Replace a Mercedes Ignition Key Lock Buzzer Switch - On Demand Video

When replacing a steering lock this little black switch can be a pain to get off

When replacing the steering lock assembly in your Benz you will need to remove that little black plastic switch on the side of the lock from the old one and put it on the new part. You can not pry it off, squeeze it off or pull it off by hand. 

Pages